Titanium 6Al4V Titanium Alloys Mechanical Chemical Physical Properties Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C Titanium 6Al4V Titanium Alloys Mechanical Chemical Physical Properties Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C

Titanium 6Al4V Titanium Alloys Mechanical Chemical Physical Properties Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C Titanium 6Al4V Grades Titanium Alloys Mechanical Chemical Physical Properties Ti 6-2-4-2 Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C Ti 15-3-3-3 Titanium 6Al4V IMI 685 Titanium Alloys Mechanical Chemical Physical Properties IMI 829 Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C CP Grade 1 CP Grade 12 CP Grade 2 CP Grade 3 CP Grade 4 CP Grade 7 / 11 / 16 Grade 5 / ELI / 23 Grade 9 / 18 Grade 19 / 20 titanioum , titan, titane, titanio, tianium, titaium, titanim, titaniom, titanium, titanum, titnium, ttanium, t1tan1um, titanium, titamium, titanimu, titanuim, titainum, titnaium, tiatnium, ttianium, ittanium, titaniu, titanim, titanum, titaium, titnium, tianium, ttanium, itanium, titaniom

- about Ti - Introduction Ind. Specification Medical Specification Applications Characteristics Classification Markets Corrosion Engineering Fabrication   - Ti Grades - Introduction Ti 6-2-4-2 Ti 15-3-3-3 Ti 13Nb-13Zr IMI 685 IMI 829 SMA CP Grade 1 CP Grade 12 CP Grade 2 CP Grade 3 CP Grade 4 CP Grade 7 / 11 / 16 6Al4V Grade 5 / 23 6Al7Nb Alloy Grade 9 / 18 Alloy Grade 19 / 20   - Ti Products - Introduction Fine Wire - Cable Foil Sheet / Plate Titanium Targets Tube Oilfield Tubes

» Titanium IMI 829

Titanex supplies this WELDABLE, HIGH STRENGTH, HIGH TEMPERATURE, CREEP RESISTANT ALLOY as a wire with max. 12 mm diameter. Ti-5.5Al-3.5Sn-3Zr-1Nb-0.25Mo-0.3Si is a weldable, high strength, high temperature (1004°F / 540°C) creep resistant alloy specifically developed for gas turbine engine components. This IMI 829 is a near alpha alloy but includes both alpha and beta stabilizer alloying elements. IMI 829 can be worked in the beta phase field, but to avoid the formation of an unacceptably large beta grain size, a process route involving alternate beta and alpha + beta working is recommended. One way to achieve this is to heat into the beta field but allow the temperature to drop into the alpha + beta field during forging.

Composition Physical Data Mechanical Data Fabrication Information

» Composition

C	< 0.08 %
N2	< 0.03 %
O2	< 0.09-0.15 %
H2	< 0.006 %
Al	5.2 - 5.7 %
Zn	3-4 %
Zr	2.5-3.5 %
Nb	0.7-1.3 %
Mo	0.2-0.35 %
Si	0.2-0.5 %
Ti =	Rem

» Physical Data

	Minimum	Typical
Density g/cm3 (lb/cu.in)		4.54(0.164)
Thermal Conductivity W/mK	6.9
*Mean Thermal Exp. Coeff. 0-100°C/°C		9.45-9.98 x 10 -6
Beta Transus °C+/-15°C(°F)		1015 (1859)

» Mechanical Data

	Minimum	Typical
Tensile Strength MPa(ksi)		930 (135)
0.2% Proof Stress MPa(ksi)		820 (119)
Elongation over 2 Inches %		9
Reduction in Area %		15
Elastic Modulus GPa(Msi)		120 (17)
@ 540 °C	Minimum	Typical
Tensile Strength MPa(ksi)		570 (83)
0.2% Proof Stress MPa(ksi)		440 (64)
Elongation over 2 Inches %		9
Reduction in Area %		25

» HEAT TREATMENT

Treatment Temperature [°F (°C)] Time Hours Cooling Method

Solution Heat Treatment

1922°F (1050°C) / 30 minutes / Air Cool or Oil Quench*

Aging Heat Treatment

1157°F (625°C) / 24 hours / Air Cool

Titanium Tantalum Molybdenum Niobium Zirconium Tungsten
Tel CH: +41 444 6353 82 Tel DE: +49 7424 9699616
REACH, RoHS compliant - Conflict Free Materials © 1994-2024 Titanex GmbH Switzerland
 

Titanium 6Al4V

Titanium Alloys Mechanical Chemical Physical Properties

Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C

Titanium 6Al4V